Magellan All-in-one Wireless Security SystemMG6250 ConsoleVersion 1.0Menu Programming Guide
Page 10System Setup: Outputs (PGMs)Enter Output Name10. Press ok. 11. Enter a name (max. 16 characters), then press ok. Set-up Activation TypesThis me
MG6250 • Menu Programming GuidePage 11ON for 30 sec.ON for 1 min.ON for 5 min.ON for 15 min.ON for 30 min.4. If desired, add other outputs (max.8
Page 12System Setup: Outputs (PGMs)4. Press one of the following:• edit: press to assign the alarm activation to areas 1, 2, or both.• next: press, se
MG6250 • Menu Programming GuidePage 136. Enter the PGM delay for output 1. 7. If desired, add another output.NOTE: Outputs (PGMs) 1 to 8 correspond to
Page 14System Setup: Keypads6. Press and hold PG1 and BYP on keypad (see a), or enter its serial number, then press ok (see b). Once completed, the ke
MG6250 • Menu Programming GuidePage 155. RepeatersMenu > 08-System Setup > Code > 05-RepeatersMenu SummaryProgramming Sequence1. Press menu.
Page 16System Setup: RepeatersEnter Repeater Name10. Press ok. 11. Enter a name (max. 16 characters), then press ok. Select Zones12. Press ok. 13. Pre
MG6250 • Menu Programming GuidePage 1719. Repeat steps 5 to 18 to add other repeaters (max. 4). Compatible ReceiversRPT1 Magellan Wireless Repeater Mo
Page 18System Setup: Doorbells6. Press Learn button on siren (see a), or enter its serial number, then press ok (see b). Once completed, the siren’s s
MG6250 • Menu Programming GuidePage 19Programming Sequence1. Press menu. 2. Select 08-System Setup menu, then press ok. 3. Enter your installer code (
Page 20System Setup: Delays/Tones13. Repeat steps 5 to 12 to add another doorbell (max. 2). 8. Delays/TonesMenu > 08-System Setup > Code > 08
MG6250 • Menu Programming GuidePage 218. Repeat steps 5 to 7 for Entry Delay 2, if desired. Once complete, press ok to access Exit Delay.Set-up Exit D
Page 22System Setup: CommunicatorSet-up Bell Squawk18. Press ok. 19. Choose whether to turn the bell squawk on or off (default is off).Set-up Pre-Alar
MG6250 • Menu Programming GuidePage 23NOTE: Pressing pause inserts a four-second pause, before the subsequent numbers are dialed.8. Choose whether you
Page 24System Setup: Communicator17. Choose whether to report when a user disarms the area selected in step 10, then press next. If yes, go to step 18
MG6250 • Menu Programming GuidePage 2528. Press ok. 29. Enter the APN (Access Point Name; max. 32 characters), then press ok.30. Enter an APN user nam
Page 26System Setup: CommunicatorAccount Setup: GSM/Land Tel #42. Press ok. 43. Select LAND or GSM as the primary communication channel, then press ne
MG6250 • Menu Programming GuidePage 2753. Repeat steps 50 to 52 for WAN 2. 54. Press ok. 55. Enter a personal, six-digit GPRS password, then press ok.
Page 28System Setup: Installer IDProgramming Sequence1. Press menu. 2. Select 08-System Setup menu, then press ok. 3. Enter your installer code (defau
MG6250 • Menu Programming GuidePage 29Set-up CallBack PC Telephone Number13. Press ok.14. Enter desired telephone number (max. 32 digits), then press
MG6250 • Menu Programming GuidePage 3IntroductionThe MG6250 All-in-one Wireless Console is a two-partition, 64-zone wireless console, offering the lat
Page 30System Setup: System Test4. Select 11-System Test sub-menu, then press ok. Test Signal StrengthThe signal strength indicators outlined in table
MG6250 • Menu Programming GuidePage 3111. After all tests are complete, press finish. Test Zones12. Press ok. 13. Trigger devices on all zones. The st
Page 32System Setup: StayD PathProgramming Sequence1. Press menu. 2. Select 08-System Setup menu, then press ok. 3. Enter your installer code (default
MG6250 • Menu Programming GuidePage 3314. Select a zone as an entry point, then press ok.NOTE: A zone can only be an entry point for one type of path
Page 34System Setup: Version Number3. Enter your installer code (default: 0000). 4. Select 13-Version Num. sub-menu, then press ok. Main Firmware Vers
MG6250 • Menu Programming GuidePage 35Trouble DisplayTable 3 provides a description of the different troubles associated with the MG6250. To view trou
Page 36NotesNotes
NotesPage 37
Page 38Notes
NotesPage 39
Page 4MG6250 • Menu Programming GuideThe Menu Flow01-BYPASS ZONES02-MESSAGES03-WAKE UP CLOCK04-CHIME ZONE05-ALARM MEMORY06-HISTORY LOG07-SYSTEM TESTNO
Page 40IndexIndexAAccess Point Name (APN) ... 25Areasentering system/site name
IndexPage 41difference between installer & maintenance codes ... 27menu summary ...
Page 42Indexadding repeaters ... 15entering repeater name ...
The whole Paradox team wishes you a successful and easy installation. We hope this product performs to your complete satisfaction. Should you have any
MG6250 • Menu Programming GuidePage 51. ZonesMenu > 08-System Setup > Code > 01-ZonesMenu SummaryProgramming Sequence1. Press menu. 2. Select
Page 6System Setup: ZonesRecord Voice Tag7. Press ok. 8. Record tag (max. 3 seconds). 9. Play, re-record (no), or save (yes) tag. NOTE: Zone tags will
MG6250 • Menu Programming GuidePage 7NOTE: To select a zone type (see Select Zone Type on page 6), either scroll the list using the next or arrow keys
Page 8System Setup: Outputs (PGMs)Modify System/Site5. Press ok. Record Voice Tag6. Press ok. 7. Record tag (max. 3 seconds).8. Play, re-record (no),
MG6250 • Menu Programming GuidePage 94. Select 03-Outputs sub-menu, then press ok. Add Output5. Select an output to add, then press ok. Choose Wireles
Comments to this Manuals